Repair guides
Step-by-step procedures for Hunter 350 maintenance and repair.
51 guides
- Demo — verification required
Replace Spark Plug
Remove, inspect, and install a new spark plug on the Hunter 350. Spark plug specification and tightening torque must be verified from the official manual before installation.
Beginner Friendly · 45 min · 17 steps
- Demo — verification required
Change Front Tyre
Remove the front wheel, replace the tyre, balance, and reinstall. Classified as advanced due to lifting, brake work, and torque-critical fasteners. All pressures and torques require official manual verification.
Advanced · 120 min · 22 steps
- Demo — verification required
Check Tyre Pressure
Measure and adjust front and rear tyre pressure when tyres are cold. Verify pressures from official manual.
Beginner Friendly · 15 min · 5 steps
- Demo — verification required
Inspect Tyre Wear
Visual and tactile inspection of tread depth, pattern, and sidewall condition.
Beginner Friendly · 10 min · 4 steps
- Demo — verification required
Remove Front Wheel
Safely elevate and remove the front wheel for service.
Intermediate · 45 min · 4 steps
- Demo — verification required
Remove Rear Wheel
Remove rear wheel for tyre, chain, or bearing service.
Intermediate · 50 min · 4 steps
- Demo — verification required
Change Rear Tyre
Replace rear tyre with balancing and correct reinstall.
Advanced · 120 min · 4 steps
- Demo — verification required
Repair a Simple Puncture
Temporary or permanent plug repair for tubeless tyres — assess suitability before riding.
Intermediate · 30 min · 4 steps
- Demo — verification required
Inspect Wheel Bearings
Check for play and roughness in front and rear wheel bearings.
Intermediate · 30 min · 3 steps
- Demo — verification required
Inspect Brake Pads
Visual inspection of pad material thickness.
Beginner Friendly · 15 min · 3 steps
- Demo — verification required
Replace Brake Pads
Replace worn front brake pads and bed in correctly.
Intermediate · 60 min · 6 steps
- Demo — verification required
Check Brake Fluid
Inspect reservoir level and fluid condition.
Beginner Friendly · 10 min · 3 steps
- Demo — verification required
Inspect Brake Discs
Check disc thickness, runout, and surface condition.
Beginner Friendly · 15 min · 3 steps
- Demo — verification required
Check Engine Oil Level
Verify oil level via sight glass or dipstick per manual.
Beginner Friendly · 10 min · 3 steps
- Demo — verification required
Change Engine Oil
Drain and refill engine oil with filter service as scheduled.
Intermediate · 60 min · 6 steps
- Demo — verification required
Replace Oil Filter
Remove and install new engine oil filter during oil service.
Intermediate · 30 min · 4 steps
- Demo — verification required
Inspect Spark Plug
Remove and visually inspect spark plug without necessarily replacing.
Beginner Friendly · 30 min · 4 steps
- Demo — verification required
Read Spark Plug Condition
Interpret plug appearance as indicators — not confirmed diagnoses.
Beginner Friendly · 15 min · 4 steps
- Demo — verification required
Inspect for Oil Leaks
Identify external oil leak sources without disassembly.
Beginner Friendly · 20 min · 3 steps
- Demo — verification required
Inspect Engine Mounting Points
Check engine mount bolts and rubber isolators for looseness or deterioration.
Beginner Friendly · 20 min · 3 steps
- Demo — verification required
Inspect Air Filter
Remove and assess air filter element condition.
Beginner Friendly · 20 min · 3 steps
- Demo — verification required
Clean Air Filter
Clean reusable foam filter if equipped — many Hunter configs use paper elements requiring replacement.
Beginner Friendly · 25 min · 3 steps
- Demo — verification required
Replace Air Filter
Install new air filter element.
Beginner Friendly · 25 min · 3 steps
- Demo — verification required
Inspect Visible Fuel Lines
Check accessible fuel hoses for cracking, weeping, or loose clamps.
Beginner Friendly · 15 min · 3 steps
- Demo — verification required
Inspect Throttle Response
Check for smooth opening and closing without sticking.
Beginner Friendly · 10 min · 3 steps
- Demo — verification required
Check Visible Loose Connectors
Inspect accessible electrical connectors for looseness or corrosion.
Beginner Friendly · 15 min · 3 steps
- Demo — verification required
Clean the Chain
Remove grit and old lube before fresh lubrication.
Beginner Friendly · 30 min · 4 steps
- Demo — verification required
Lubricate the Chain
Apply chain lube to inner link plates after cleaning.
Beginner Friendly · 15 min · 3 steps
- Demo — verification required
Inspect Chain Slack
Measure slack at tightest point on lower chain run.
Beginner Friendly · 10 min · 3 steps
- Demo — verification required
Adjust Chain Tension
Set chain slack via rear axle adjusters equally.
Intermediate · 45 min · 4 steps
- Demo — verification required
Inspect Sprocket Wear
Check tooth profile for hooked or sharpened teeth.
Beginner Friendly · 15 min · 3 steps
- Demo — verification required
Check Clutch Free Play
Measure free play at lever before cable pulls clutch.
Beginner Friendly · 10 min · 2 steps
- Demo — verification required
Adjust Clutch Cable
Set clutch cable free play at handlebar adjuster and/or engine end.
Beginner Friendly · 20 min · 3 steps
- Demo — verification required
Check Throttle Free Play
Verify small gap before throttle opens at grip.
Beginner Friendly · 10 min · 2 steps
- Demo — verification required
Inspect Control Cables
Check clutch and throttle cables for fraying and routing.
Beginner Friendly · 15 min · 3 steps
- Demo — verification required
Inspect Battery Terminals
Clean and tighten battery connections.
Beginner Friendly · 15 min · 3 steps
- Demo — verification required
Check Battery Condition
Assess battery state of charge and cranking performance.
Beginner Friendly · 15 min · 3 steps
- Demo — verification required
Replace Battery
Remove and install compatible 12 V battery.
Beginner Friendly · 30 min · 4 steps
- Demo — verification required
Check Fuse Condition
Inspect fuses in fuse box for blown elements.
Beginner Friendly · 10 min · 3 steps
- Demo — verification required
Replace a Fuse
Install correct rating fuse only.
Beginner Friendly · 10 min · 3 steps
- Demo — verification required
Inspect Visible Wiring
Look for chafed insulation and poor repairs.
Beginner Friendly · 20 min · 3 steps
- Demo — verification required
Replace Accessible Bulbs
Replace headlight, tail, or indicator bulbs with compatible homologated parts.
Beginner Friendly · 20 min · 3 steps
- Demo — verification required
Diagnose Basic No-Start
Initial checks when engine does not start — not a confirmed diagnosis.
Beginner Friendly · 25 min · 5 steps
- Demo — verification required
Pre-Ride Inspection
T-CLOCS-style check before every ride.
Beginner Friendly · 10 min · 5 steps
- Demo — verification required
Periodic Fastener Inspection
Check critical fasteners for looseness.
Beginner Friendly · 30 min · 4 steps
- Demo — verification required
Inspect Side Stand
Check stand, spring, and cut-out switch operation.
Beginner Friendly · 10 min · 3 steps
- Demo — verification required
Inspect Lights and Indicators
Verify all lights function correctly.
Beginner Friendly · 10 min · 3 steps
- Demo — verification required
Inspect Horn
Confirm horn operates for road legal use.
Beginner Friendly · 5 min · 2 steps
- Demo — verification required
Wash Motorcycle Safely
Clean without damaging electrical and bearing components.
Beginner Friendly · 45 min · 3 steps
- Demo — verification required
Prepare for Storage
Long-term storage preparation to protect fuel system and battery.
Beginner Friendly · 60 min · 5 steps
- Demo — verification required
Post-Storage Inspection
Checks before first ride after storage.
Beginner Friendly · 30 min · 4 steps